XTREME Original Klearkote 4.4 VOC
$ 95.05
- Description Items Included 5185 | Original Klearkote – 4.4 VOC (1 Gallon/3.785 Liters) 5187 | Original Hardener Medium – 4.4 VOC(1 Quart/.946 Liters) A medium solids two component polyurethane clearcoat with a sprayable VOC of 4.4 lbs/gal. Formulated to offer Refinishers ease of application, great flow and leveling, superior gloss and excellent distinctness of image in a productive 2K polyurethane clearcoat. TECH DATA: Mix Ratio : 4 parts clearcoat: 1 part hardener Catalyst: #5186 Fast, #5187 Medium, #5188 Slow Viscosity (Sprayable): 17-19 seconds #2 Zahn Suggested Fluid Tip Size*: Siphon (1.3mm – 1.5mm) Gravity (1.3mm – 1.5mm) HVLP (1.3mm – 1.5mm) Volume Solids (Sprayable): 33% Film Build: 0.8 – 1.0 mils per full wet coat Coverage: 465 Sq. Ft. per gallon @ 1 mil V.O.C. (Sprayable): 4.4 lbs/gallon Pot Life: 4-5 Hours with #5186, 8-10 hours with #5187 or#5188 5 STAR XTREME AUTOBODY PRODUCTS TECHNICAL DATA INFORMATION DATED: JUNE 2013 PRODUCT NUMBER DESCRIPTION #5185 – ORIGINAL KLEARKOTE 4.4 VOC PRODUCT DESCRIPTION 5185 is a medium solids two component polyurethane clearcoat with a sprayable VOC of 4.4 lbs/gal. Formulated to offer Refinishers ease of application, great flow and leveling, superior gloss and excellent distinctness of image in a productive 2K polyurethane clearcoat. PRODUCTS #5185-1 Original Klearkote, Gallon #5185-4 Original Klearkote, Quart *#5186 Original Hardener, Fast 4.4 VOC Quart *#5187 Original Hardener, Medium 4.4 VOC Quart *#5188 Original Hardener, Slow 4.4 VOC Quart * Also available in half pints CAUTION ACCELERATOR NOT RECOMMENDED SURFACE PREPARATION Apply Undercoats and Basecoat per manufacturer’s instruction. Over OEM or completely cured previously painted substrates scuff with a grey scuff pad or 600 grit then wipe clean with #5902 Final Wipe Surface Cleaner. Allow basecoat adequate flash time (follow manufacturer’s recommendation) Follow basecoat manufacturer’s recommendation for recoat intervals. MIXING DIRECTIONS Mix 4 parts 5185 base with 1 part 5186, 5187, or 5188 by volume. Activator selection should be based on the size of the part to be painted and the temperature of both the air and part at time of painting. APPLICATION Number of Coats: 2-3 Application Density: full wet coats Overlap: 50% Flash: Follow recommendations in “Dry Time” section Film Thickness Range: Dry 1 mil – 6 mils Wet 3 mils – 6 mils Application Conditions: Minimum Temp 50°F (Substrate Temp.) Max Temp 100°F (Substrate Temp.) Ambient Humidity Less than 80% preferred POT LIFE When properly covered at 77°F, 5185 will maintain a sprayable viscosity for at least from 3-5 hours depending on activator selection. ADDITIVES ACCELERATOR: N/A FISHEYE: N/A FLEX ADDITIVE: Not required Note: Do not spray when surface temperature is below 50°F. SUBSTRATES Commercially available basecoats with a VOC of less than 6.6 lbs/gal. Properly prepared previously painted surfaces. CLEAN-UP & STORAGE Clean spray equipment immediately after use with gun wash solvent. GUN SETUPS: CONVENTIONAL Gravity Feed 1.3 – 1.5 mm tip Siphon Feed 1.6 – 1.8 mm tip HVLP 1.3 mm – 1.5 mm AIR PRESSURES Conventional @ Gun PANEL OVERALL Gravity Feed 35-40 psi 45 psi Siphon Feed 35-45 psi 45-50 psi HVLP @ Cap 6-8 psi 9-10 psi FLASH/DRY TIMES 5186 @ or 5187 @ or 5188 @ or above 77ºF above 85ºF above 95ºF Flash Between Coats 5-10 min 5-10 min 10-15 min Dust Free 10-15 min 15 min 15-20 min Sand/Polish 8-10 hours 10-12 hours 12-14 hours Force Dry (Convection Heat) 5186 5187 5188 Purge time before applying heat 20 min 20 min 20 min Force Dry Time 20 min@ 165ºF 20 min@ 165ºF 20 min@ 165ºF Sand and Buff After Cool Down TECHNICAL DATA Density: 7.64 lbs/gal (unactivated) Solids By Weight: 36.2% By Volume: 29.0% VOC (Volatile Organic Content): 4.56 lbs/gal Viscosity: 17-19 seconds Zahn #2 Flash Point: -4°F Theoretical Coverage: 465 sq ft per gal @ 1 mil thickness FIRST AID: In case of eye contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention. For skin: Wash thoroughly with water. If difficulty in breathing is experienced, get medical attention immediately. If swallowed, do not induce vomiting, get medical attention immediately. See Material Safety Data Sheet. SAFETY INFORMATION – FOR INDUSTRY USE ONLY Danger: Vapor and spray mist harmful. Overspray may cause lung damage. May cause allergic skin and respiratory reaction, effects may be permanent. Flammable liquid and vapor. Harmful if inhaled.May affect the brain or nervous system causing dizziness, headache, or nausea. May cause eye, skin, nose, and throat irritation. Contents: See product label for contents and CAS #’s.The contents of this package must be blended with other components before the product can be used. Any mixture of components will have hazards of all components. Before opening the packages, read all warning labels. Follow all precautions. The material is designed for application only by professional trained personnel using proper equipment under controlled conditions, and is not intended for sale to the general public. KEEP OUT OF REACH OF CHILDREN.
Starfire Urethane Clear Coat – 2657
Starfire Wet Look Acrylic Enamel Hardener
5 Star Original Hardener